CleanCide Wipes

Citric acid-based CleanCide germicidal wipes deliver powerful efficacy against pathogens—without the potentially harmful effects of other chemical disinfectants—in an easy-to-use wipe.

Powerful disinfection—broad efficacy:

  • Kills 99.9% of household germs
  • Eliminates odor-causing bacteria
  • Low pH
  • Virucidal, germicidal, fungicidal and tuberculocidal efficacy
  • Effective against antibiotic resistant organisms
  • Effective against Norovirus

 

Non-irritating

  • No quats or bleach
  • EPA category IV (lowest level of toxicity)
  • No precautionary statements/PPE
  • Will not irritate skin, eyes or lungs
  • Highly biodegradable ingredients—no harmful or irritating residues

One-step, no-rinse cleaning & disinfection:

  • Proven efficacy in the presence of 5% organic soil load
  • 5-minute contact time for disinfection
  • No pre-cleaning or post-rinsing steps required

Directions for use

A two-step process of cleaning prior to disinfection is required only when surfaces are grossly soiled or there is the possibility of contamination with blood or body fluid. Clean-Cide Wipes can be used for both cleaning and disinfecting.

  1. Always wear gloves when cleaning. These wipes are for cleaning surfaces, not for use on skin. Wear a cover gown and face protection in addition to gloves if cleaning up a large body fluid spill.
  2. Pull cloth wipe from the container at 90° angle making certain to position the wipe between the two pointing arrows appearing on the lid. This permits easy separation of cloths at perforation.
  3. Unfold cloth and wipe surfaces until visibly wet. Allow solution to air dry.
    • Do not wipe the surface dry prior to adequate contact time. Wexford disinfectants contain humectants which evaporate slowly to prolong drying time. Although the surfaces may appear dry, there is still dampness or moisture present. This ensures complete bacteria kill.
  4. Wipe or rinse any residual, after sufficient contact time, from shiny surfaces if needed.
  5. Keep small center cap closed to prevent moisture loss from container.

 

Procedure for Cleaning and DisinfectingUsing Wexford CleanCide WipesOn Equipment and Cords

  1. CleanCide Wipes are for cleaning surfaces only, not for use on skin.
  2. Pull cloth wipe from the container at 90° angle making certain to position the wipe between the two pointing arrows appearing on the lid. This permits easy separation of cloths at perforation.
  3. Unfold cloth.
  4. Start at the connectors and wet down but do not saturate the cables while wiping away from the connectors. It is sometimes necessary to wring out the towelettes to avoid excess fluid on the cables. Allow solution on cables to air dry.
  5. Do not allow any solution from the towelettes to drip into the cord connectors.
  6. If pooling occurs at the cord connectors, allow adequate contact time and then dry the connectors before reuse.
  7. Cords and equipment should not be saturated.
  8. Do not wipe the surface dry prior to adequate contact time.
  9. Wipe or rinse any residual, after sufficient contact time, if needed.
  10. Allow cords to dry before packaging the equipment for reuse.
  11. Keep small center cap closed to prevent moisture loss from container.
  12. A two-step process of cleaning prior to disinfection is required only when surfaces are grossly soiled or there is the possibility of contamination with blood or body fluid. CleanCide Wipes can be used for both cleaning and disinfecting.

A Great disinfectant for:

  • Schools
  • Daycare and Nurseries
  • Hospitals and Long-Term Care Facilities
  • Office Buildings
  • Hospitality
  • Households
  • Dental

 

For use on hard, non-porous surfaces:

  • Stainless steel
  • Chrome
  • Glass
  • Plastic
  • Vinyl

Certifications

Available Sizes

Product Labels

Ingredients

CAS Number Ingredient Function
7732-18-5
Water
Solvent
142-31-4
Sodium Octyl Sulfate
Surfactant
79-33-4
Lactic Acid
Acidifier
617-48-1
Malic Acid
Acidifier
64-19-7
Acetic Acid
Acidifier
112-05-0
Pelargonic Acid
Acidifier, Defoamer
77-92-9
Citric Acid
Active Ingredient
68439-57-6
Sodium C14-16 Olefin Sulfonate
Surfactant
68037-05-8
Ammonium C6-10-alkyl Polyoxyethylene Sulfate
Surfactant
68131-39-5
C12-15 Alcohols Ethoxylated
Surfactant

Powerful disinfection—broad efficacy:

  • Kills 99.9% of household germs
  • Eliminates odor-causing bacteria
  • Low pH
  • Virucidal, germicidal, fungicidal and tuberculocidal efficacy
  • Effective against antibiotic resistant organisms
  • Effective against Norovirus

 

Non-irritating

  • No quats or bleach
  • EPA category IV (lowest level of toxicity)
  • No precautionary statements/PPE
  • Will not irritate skin, eyes or lungs
  • Highly biodegradable ingredients—no harmful or irritating residues

 

One-step, no-rinse cleaning & disinfection:

  • Proven efficacy in the presence of 5% organic soil load
  • 5-minute contact time for disinfection; 1-minute contact time for sanitization1
  • No pre-cleaning or post-rinsing steps required

Directions for use

A two-step process of cleaning prior to disinfection is required only when surfaces are grossly soiled or there is the possibility of contamination with blood or body fluid. Clean-Cide Wipes can be used for both cleaning and disinfecting.

  1. Always wear gloves when cleaning. These wipes are for cleaning surfaces, not for use on skin. Wear a cover gown and face protection in addition to gloves if cleaning up a large body fluid spill.
  2. Pull cloth wipe from the container at 90° angle making certain to position the wipe between the two pointing arrows appearing on the lid. This permits easy separation of cloths at perforation.
  3. Unfold cloth and wipe surfaces until visibly wet. Allow solution to air dry.
    • Do not wipe the surface dry prior to adequate contact time. Wexford disinfectants contain humectants which evaporate slowly to prolong drying time. Although the surfaces may appear dry, there is still dampness or moisture present. This ensures complete bacteria kill.
  4. Wipe or rinse any residual, after sufficient contact time, from shiny surfaces if needed.
  5. Keep small center cap closed to prevent moisture loss from container.

 

Procedure for Cleaning and DisinfectingUsing Wexford CleanCide WipesOn Equipment and Cords

  1. CleanCide Wipes are for cleaning surfaces only, not for use on skin.
  2. Pull cloth wipe from the container at 90° angle making certain to position the wipe between the two pointing arrows appearing on the lid. This permits easy separation of cloths at perforation.
  3. Unfold cloth.
  4. Start at the connectors and wet down but do not saturate the cables while wiping away from the connectors. It is sometimes necessary to wring out the towelettes to avoid excess fluid on the cables. Allow solution on cables to air dry.
  5. Do not allow any solution from the towelettes to drip into the cord connectors.
  6. If pooling occurs at the cord connectors, allow adequate contact time and then dry the connectors before reuse.
  7. Cords and equipment should not be saturated.
  8. Do not wipe the surface dry prior to adequate contact time.
  9. Wipe or rinse any residual, after sufficient contact time, if needed.
  10. Allow cords to dry before packaging the equipment for reuse.
  11. Keep small center cap closed to prevent moisture loss from container.
  12. A two-step process of cleaning prior to disinfection is required only when surfaces are grossly soiled or there is the possibility of contamination with blood or body fluid. CleanCide Wipes can be used for both cleaning and disinfecting.

A Great disinfectant for:

  • Schools
  • Daycare and Nurseries
  • Hospitals and Long-Term Care Facilities
  • Office Buildings
  • Hospitality
  • Households
  • Dental

 

For use on hard, non-porous surfaces:

  • Stainless steel
  • Chrome
  • Glass
  • Plastic
  • Vinyl

Certifications

Available Sizes

Product Labels

Ingredients

CAS Number Ingredient Function
7732-18-5
Water
Solvent
142-31-4
Sodium Octyl Sulfate
Surfactant
79-33-4
Lactic Acid
Acidifier
617-48-1
Malic Acid
Acidifier
64-19-7
Acetic Acid
Acidifier
112-05-0
Pelargonic Acid
Acidifier, Defoamer
77-92-9
Citric Acid
Active Ingredient
68439-57-6
Sodium C14-16 Olefin Sulfonate
Surfactant
68037-05-8
Ammonium C6-10-alkyl Polyoxyethylene Sulfate
Surfactant
68131-39-5
C12-15 Alcohols Ethoxylated
Surfactant

KILLS 99.9% OF HOUSEHOLD GERMS

EPA LIST N
APPROVED

HOSPITAL
GRADE

CITRIC ACID
BASED

QUAT AND
BLEACH FREE